## How To Calculate A Gradient For Drainage, Ramps, Slopes Etc

We Show You How To Calculate Slopes & Gradients By Hand and Using Our Free To Use Calculators

Article By: Tom Ayre | Last Update: November 2020

Calculating a gradient slope is an important element of any building and civil engineering design project. Gradients are crucial to several elements of construction. Typical situations to in which you will need to calculate a gradient are:

- Pipe drainage fall rates – without a correct gradient the water in the pipe may not flow.
- Access ramps – standards are very strict on things like disability ramps.
- Stairs – like access ramps, stairs are a very important element to get right in terms of gradient/slope design.

In this blog article, I will be showing you how to calculate the gradient by hand which will be useful for sites where you don’t have a calculator. We also have a calculator for each section making the process even easier.

#### Table of Contents

### Introduction to Gradients

A gradient is a complicated word for quite a simple concept. The gradient refers to the change rate or how steep a slope is.

Take for instance a gradient of slope that is 1 in 100 (1:100)

A 1:100 slope means that for every 100 metres along the ground, the slope height increases or decreases by 1 metre. A 1:0.5 slope means that for every 1 metre along the ground, the slope height increases by 0.5 metres.

A gradient can be expressed in 2 ways, a number or a ratio.

For instance, a 1:40 gradient number is shown as 0.025 (an example is shown in the calculation section).

The same number can be converted into a ratio

For instance, a ratio is shown as “1:40”

The following sketch should help.

Prior to calculating your gradients it is useful to know ground levels to calculate elements such as muck away volumes, pipe lengths etc. Consider employing a setting out engineer / company to undertake a precise topographical survey of the site to get this as accurate as possible!

### Calculate a Gradient Number

So how do you calculate a gradient number? This is very simple. Just make sure you keep your run/rise units the same (meters, centimetres, miles, km etc)

**Step 1:** Work out the run length. This is the horizontal distance along the ground. Example number 60 metres.

**Step 2:** Work out the rise length. This is the vertical length going up. Example number 12 metres.

**Step 3:** Divide the rise length by the run length, in a calculator this would be 12 ÷ 60. This would equal a gradient of 0.2.

#### Gradient Number Hand Calculation

**Example 1**

Run length = 25 metres

Rise Length = 0.8 metres

Gradient = 0.8 / 25

Gradient = 0.032

**Example 2**

Run Length = 500 mm

Rise Length = 1200 mm

Gradient = 1200 / 500

Gradient = 2.4

#### Gradient Number Online Calculator

Make sure you use the same units in both the run and the rise calculators. So keep things in metres, millimeters, centimetres etc.

THS Concepts undertake topographical surveys for Architects & designers looking to design their projects more effectively.

### Calculate a Gradient Slope Percentage

So how do you calculate a gradient slope %? Again, this is very simple. Just make sure you keep your run/rise units the same (meters, centimetres, miles, km etc)

**Step 1:** Work out the run length. This is the horizontal distance along the ground. Example number 60 metres.

**Step 2:** Work out the rise length. This is the vertical length going up. Example number 12 metres.

**Step 3:** Divide the rise length by the run length, in a calculator this would be 12 ÷ 60. This would equal a gradient slope of 0.2 which is 20% (multiply by 100 if you need to).

#### Gradient Slope Percentage Hand Calculation

**Example Calculation 1**

Run length = 25 metres

Rise Length = 0.8 metres

Gradient = 0.8/ 25 Gradient %= 0.032

Gradient % = 0.032 x 100

Gradient % =3.2

**Example Calculation 2**

Run length = 3200 mm

Rise Length = 750 mm

Gradient = 750/ 3200 Gradient % = 0.234%

Gradient % = 0.234 x 100

Gradient % = 23.438%

#### Gradient Slope Percentage Online Calculator

Make sure you use the same units in both the run and the rise calculators. So keep things in metres, millimeters, centimetres etc.

### Calculate a Gradient Ratio

So how do you calculate a gradient ratio? Another bit of easy maths. Just make sure you keep your run/rise units the same (meters, centimetres, miles, km etc)

**Step 1:** Work out the run length. This is the horizontal distance along the ground. Example number 60 metres.

**Step 2:** Work out the rise length. This is the vertical length going up. Example number 12 metres.

**Step 3:** Divide the run length by the rise length, in a calculator this would be 60 ÷ 12 . This would equal a gradient of 5, this would then be shown as a ratio so = 1:5

#### Gradient Ratio Hand Calculation

**Example Calculation 1**

Run length = 25 metres

Rise Length = 0.8 metres

Gradient = 25/ 0.8

Gradient = 1:31.25

**Example Calculation 2**

Run Length = 500 mm

Rise Length = 1200 mm

Gradient = 500/ 1200

Gradient = 1:0.4166

#### Gradient Slope Percentage Online Calculator

Make sure you use the same units in both the run and the rise calculators. So keep things in metres, millimeters, centimetres etc.

### Calculate Pipe Rise / Fall

If you know what your pipe needs to fall at (example 1:40, 1:20 etc) then you will need to know what the pipe needs to drop by over the length of the pipe.

**Step 1:** Work out the run length. This is the horizontal distance along the ground. Example number 60 metres.

**Step 2:** Work out required fall ratio (usually specified by designer). Example fall is 1:30

**Step 3:** Divide the horizontal distance by the fall number. Example would be 60 ÷ 30. Your fall in pipe therefore equals 2 metres.

#### Pipe Rise / Fall Hand Calculation

**Example Calculation 1**

Run length = 25 metres

Fall ratio = 1:80

Pipe fall = 25 ÷ 80

Pipe fall = 0.3125 m

**Example Calculation 1**

Run length = 3250 mm

Fall ratio = 1:40

Pipe fall = 3250 ÷ 40

Pipe fall = 81.25 mm

#### Pipe Rise / Fall Hand Online Calculator

#### Pipe Rise / Fall Table

### How To Set Out A Gradient

Setting out a gradient for an important project should be undertaken by a reputable setting out survey company.

Prior to the setting out a topographical survey of the site should be undertaken to establish precise levels. This will help calculate muck away volumes, costs, pipes required etc.

Below we show a very simple method to setting out gradients without expensive equipment. Of course, this should only be utilised on small domestic projects where it is not so important you are spot on accurate!

#### Materials Needed

- 2 long timber stakes (1.2m)
- mallet
- 1 spirt level
- 1 string line
- measuring tape 5m
- long tape 30 m
- permanent marker

#### Method

**Step 1** – Start by placing your timber pegs at the start and end of your drainage run. Using your mallet, bang the rods into the ground so they are nice and vertical and solid in the ground.

**Step 2** – Using your string line, nail the string at the midway point on the first stake. Take the string line to the other stake and using your spirit level try to get the line as level as possible. You may need a second pair of hands. Level the line all the way along as best you can and ensure it is taught. This may take some time! Once you have done this use your permanent marker to mark the height of the string line at each peg.

Step 3 – Using your 30m tape, measure the distance between of the string you have just placed. Write down this number.

**Step 4 –** You now need to calculate the fall (drop) of your gradient over that length. You should know the fall ratio of your pipe, this could be 1:40 , 1:100 etc. You can now use the calculator above “How to Calculate Pipe Rise / Fall”. Here you can plug in your distance between your stakes and the ratio of the pipe. This calculator will then give you the vertical distance down / up.

**Step 5 – **Now, using your the fall distance you previously calculated, you will bring down the string line on one of the pegs. You will need a tape measure to measure down from the mark that you made on the peg in the previous step. Following this you should now have a string line set to the correct fall gradient.

**Step 6** – You can now use your tape measure or spirt level to set out the gradient from this line. You might decide that your pipe needs to be 1 m down from this line. If so, make sure you are measuring down from the line by 1 metre at every location!

### Gradients For Drainage

Current British Standard guidelines for drainage and sewer systems can be found here. Please check this standard prior to placing drainage schemes to ensure you are compliant.

#### Rainwater Drains

- Rainwater drains at 75 & 100 mm should be laid at ratios of
**1:100**or less. - Rainwater drains at 150 mm should be laid at ratios of
**1:150**or less. - Rainwater drains at 225 mm should be laid at ratios of
**1:225**or less.

#### Waste Water Pipes (Self Cleaning)

- Flows Less Than 1 litre per second (pipes not exceeding DN100) – should be laid at ratios of
**1:40**or less. - Flows More Than 1 litre per second (pipes not exceeding DN100) – should be laid at ratios of
**1:80**or less with at least 1 toilet connected to it. - DN150 pipe – should be laid at ratios of
**1:150**or less with at least 5 toilets connected to it.

### Gradients For Wheelchair Ramps

Current British Standard guidelines for drainage and sewer systems can be found here. Please check this standard prior to placing drainage schemes to ensure you are compliant.

#### Rainwater Drains

- Rainwater drains at 75 & 100 mm should be laid at ratios of
**1:100**or less. - Rainwater drains at 150 mm should be laid at ratios of
**1:150**or less. - Rainwater drains at 225 mm should be laid at ratios of
**1:225**or less.

#### Waste Water Pipes (Self Cleaning)

- Flows Less Than 1 litre per second (pipes not exceeding DN100) – should be laid at ratios of
**1:40**or less. - Flows More Than 1 litre per second (pipes not exceeding DN100) – should be laid at ratios of
**1:80**or less with at least 1 toilet connected to it. - DN150 pipe – should be laid at ratios of
**1:150**or less with at least 5 toilets connected to it.